Found issues when using ## to concatenate tokens in macros where the
resulting symbolic names were including the ## tokens themselves. Using
CONCAT everywhere fixes the issue.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
This reverts commit 3ba4c98a1d.
A repo from microsoft was not available, that lead to ci
actions failing. This hat been fixed, so this workaround
is no longer needed.
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
Currently the USB configuration of this sample is
selecting POSIX_CLOCK and being built by default with
USB_NATIVE_POSIX. This combination is currently not possible
due to mutually exclusive dependencies (the host C library)
which results in a configuration warning and POSIX_CLOCK being
forced to 'n'.
Let's instead disable POSIX_CLOCK in this sample USB config
overlay, until the USB native driver supports building
with embedded C libraries.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Removing ourselves from maintainers list as we currently don't have
bandwidth to maintain this platform family.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
With the changes made in pull request #68741, RPMsg service is
supported on stm32h747i_disco using the STM32 HSEM IPM driver. For the
sample to work, add device tree overlays to enable the mailbox and set
the shared memory appropriately.
Signed-off-by: Celina Sophie Kalus <hello@celinakalus.de>
1. support the baudrate = 3MHz.
2. add baudrate = 115200 setting when UART source clock = 25/30/48/50 MHz.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
This commit implement the UART asynchronous API mode support.
When the API is used, the UART hardware cooperates with the DMA (MDMA)
module to handle the the data transfer and receiving.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Pytest harness in Twister tries to get custom parameters to
the pytest harnesses. It is required although those do not exist
(e.g. Twister uses devices without hw map). This change checks
if the custom parameters to the pytest harnesses exists.
Fixes#71817
Signed-off-by: Katarzyna Giądła <katarzyna.giadla@nordicsemi.no>
Instead of chapters, make device runtime power management and
system-managed device power management sections.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
There is a whole section dedicated to power domains. The brief
information in device power management was not adding anything.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Commit adds optimization of blob and dfu models bsim tests.
1. Makes general transfer size and block size smaller for blob.
2. Makes waiting time shorter for some blob bsim tests.
3. Splits long dfu srv persistence test suite into two.
4. Reduces retransmission for unicast messages till zero
for blob and dfu tests.
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
Commit fixes bug if dfu server failed to deliver
apply response it gets stuck in applying phase.
In this phase it skips all further client attempts
to apply image again.
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
Rename the Kconfig symbol for all ITE SoC variants.
Rename the SOC_SERITES_ITE_IT8XXX2 to SOC_SERIES_IT8XXX2.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Using the SOC_IT8XXX2_REG_SET_V2 instead of constantly adding new
variants of the IT82XX2 SoC.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Make the --list-tests and --tests-tree options outputs
respect the --tag and --exclude-tag options,
so that only the tests for the specified tags are listed.
Also update the TestPlan report testcases for this change.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Backend index must also be incremented, when backend is not an autostart
backend. Otherwise, the resulting bit field can not be used to address
a backend by index; autostart field would have to be taken into account.
Signed-off-by: Torsten Robitzki <Torsten@Robitzki.de>
Adds a handler to check error flag bits. This should be called
by applications that call regulator_enable and receive -EINVAL
as a return.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Adds support for the PGOOD pin. This pin is asserted by the
regulator when converter startup has completed and the output
is stable. If the PGOOD pin is not used, the PGOOD state is
check via the PGOOD_PIN_STS bit.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Enables the converter via I2C as the else case when the EN pin
conditional fails. This used to not matter as no code followed,
but this will change in subsequent patches.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Example of usage of HCI vendor specific Set Scan Request Reports
command, Scan Request Received Event and corresponding callback
to get application events. The sample application shows usage as an
alternative to extended advertisent saving precious RAM.
Signed-off-by: Giancarlo Stasi <giancarlo.stasi.co@gmail.com>
Ignore failure to Broadcast ISO remove data path when
terminating a BIG without a data path being setup.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
When multiple advertisers overlap over time, the random
delay being applied need many ticker operation context.
This causes the ticker_update interface to return error
causing assertion in the Controller.
This is fixed by not applying random_delay value to the
overlapping advertiser that does not get to use the radio.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This reverts commit 9b43fed10a.
This PR introduced 2 regressions in main CI:
71977 & 71978
Let's revert it by now to get main's CI passing again.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This reverts commit 93dc7e7438.
This PR introduced 2 regressions in main CI:
71977 & 71978
Let's revert it by now to get main's CI passing again.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This reverts commit 61c70626a5.
This PR introduced 2 regressions in main CI:
71977 & 71978
Let's revert it by now to get main's CI passing again.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This reverts commit 3ef282be6c.
This PR introduced 2 regressions in main CI:
71977 & 71978
Let's revert it by now to get main's CI passing again.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This reverts commit 9f4d9989c6.
This PR introduced 2 regressions in main CI:
71977 & 71978
Let's revert it by now to get main's CI passing again.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This reverts commit 20611f13ca.
This PR introduced 2 regressions in main CI:
71977 & 71978
Let's revert it by now to get main's CI passing again.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This reverts commit 02b24911f7.
This PR introduced 2 regressions in main CI:
71977 & 71978
Let's revert it by now to get main's CI passing again.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
With the deprecation of `BT_LE_ADV_OPT_USE_NAME` and
`BT_LE_ADV_OPT_FORCE_NAME_IN_AD` samples were updated to not use the
macro adding the device name in the advertising/scan response data
anymore.
Instead the name was explicitly added to the scan response data in
`periodic_adv` sample. But because it was using an extended advertiser
and was already adding data in the AD, the name should have been put in
the advertising data and not the scan response data.
Update the sample to add the device name in the advertising data.
Signed-off-by: Théo Battrel <theo.battrel@nordicsemi.no>
With the deprecation of `BT_LE_ADV_OPT_USE_NAME` and
`BT_LE_ADV_OPT_FORCE_NAME_IN_AD` the tester has been updated to not use
the macro adding the device name in the advertising/scan response data
anymore. Instead the name was explicitly added to the scan response
data. But because that part of the tester was using an extended
advertiser and was already adding data in the AD, the name should have
been put in the advertising data and not the scan response data.
The same issue apply to both `btp_cap.c` and `btp_bap_broadcast.c`,
update them to add the device name in the advertising data.
Signed-off-by: Théo Battrel <theo.battrel@nordicsemi.no>
Tom Burdick