263 lines
7.7 KiB
C
263 lines
7.7 KiB
C
/* Copyright 2018 The Chromium OS Authors. All rights reserved.
|
|
* Use of this source code is governed by a BSD-style license that can be
|
|
* found in the LICENSE file.
|
|
*/
|
|
|
|
/* Nocturne board configuration */
|
|
|
|
#ifndef __CROS_EC_BOARD_H
|
|
#define __CROS_EC_BOARD_H
|
|
|
|
/*
|
|
* By default, enable all console messages excepted HC, ACPI and event:
|
|
* The sensor stack is generating a lot of activity.
|
|
*/
|
|
#define CC_DEFAULT (CC_ALL & ~(CC_MASK(CC_EVENTS) | CC_MASK(CC_LPC)))
|
|
#undef CONFIG_HOSTCMD_DEBUG_MODE
|
|
#define CONFIG_HOSTCMD_DEBUG_MODE HCDEBUG_OFF
|
|
|
|
#define CONFIG_SUPPRESSED_HOST_COMMANDS \
|
|
EC_CMD_CONSOLE_SNAPSHOT, EC_CMD_CONSOLE_READ, EC_CMD_PD_GET_LOG_ENTRY
|
|
|
|
/* NPCX7 config */
|
|
#define NPCX_UART_MODULE2 1 /* GPIO64/65 are used as UART pins. */
|
|
#define NPCX_TACH_SEL2 0 /* No tach. */
|
|
#define NPCX7_PWM1_SEL 0 /* GPIO C2 is not used as PWM1. */
|
|
#define CONFIG_HIBERNATE_PSL
|
|
|
|
/* Internal SPI flash on NPCX7 */
|
|
#define CONFIG_FLASH_SIZE (512 * 1024) /* It's really 1MB. */
|
|
#define CONFIG_SPI_FLASH_REGS
|
|
#define CONFIG_SPI_FLASH_W25Q80 /* Internal SPI flash type. */
|
|
|
|
/* EC modules */
|
|
#define CONFIG_ADC
|
|
#define CONFIG_BACKLIGHT_LID
|
|
#define CONFIG_BOARD_VERSION_CUSTOM
|
|
#define CONFIG_HOSTCMD_ESPI
|
|
#define CONFIG_I2C
|
|
#define CONFIG_I2C_BUS_MAY_BE_UNPOWERED
|
|
#define CONFIG_I2C_MASTER
|
|
#define CONFIG_LOW_POWER_IDLE
|
|
#define CONFIG_PWM
|
|
#define CONFIG_VBOOT_HASH
|
|
#define CONFIG_VSTORE
|
|
#define CONFIG_VSTORE_SLOT_COUNT 1
|
|
|
|
#define CONFIG_DETACHABLE_BASE
|
|
|
|
/* EC console commands */
|
|
#define CONFIG_CMD_ACCELS
|
|
#define CONFIG_CMD_ACCEL_INFO
|
|
#define CONFIG_CMD_BUTTON
|
|
#define CONFIG_CMD_PD_CONTROL
|
|
#define CONFIG_CMD_PPC_DUMP
|
|
|
|
/* Battery */
|
|
#define CONFIG_BATTERY_CUT_OFF
|
|
#define CONFIG_BATTERY_SMART
|
|
#define CONFIG_BATTERY_REVIVE_DISCONNECT
|
|
#define CONFIG_BATTERY_PRESENT_GPIO GPIO_BAT_PRESENT_L
|
|
|
|
/* Buttons / Switches */
|
|
#define CONFIG_BASE_ATTACHED_SWITCH
|
|
#define CONFIG_BUTTON_TRIGGERED_RECOVERY
|
|
#define CONFIG_VOLUME_BUTTONS
|
|
|
|
/* Charger */
|
|
#define CONFIG_CHARGE_MANAGER
|
|
#define CONFIG_CHARGER
|
|
#define CONFIG_CHARGER_DISCHARGE_ON_AC
|
|
#define CONFIG_CHARGER_INPUT_CURRENT 128
|
|
#define CONFIG_CHARGER_ISL9238
|
|
#define CONFIG_CHARGER_MIN_BAT_PCT_FOR_POWER_ON 1
|
|
#define CONFIG_CHARGER_SENSE_RESISTOR 10
|
|
#define CONFIG_CHARGER_SENSE_RESISTOR_AC 20
|
|
#define CONFIG_CHARGER_V2
|
|
#define CONFIG_EXTPOWER_GPIO
|
|
|
|
/* LEDs */
|
|
#define CONFIG_LED_COMMON
|
|
#define CONFIG_LED_PWM_ACTIVE_CHARGE_PORT_ONLY
|
|
#define CONFIG_LED_PWM_COUNT 2
|
|
#undef CONFIG_LED_PWM_NEAR_FULL_COLOR
|
|
#define CONFIG_LED_PWM_NEAR_FULL_COLOR EC_LED_COLOR_WHITE
|
|
|
|
/* MKBP */
|
|
#define CONFIG_MKBP_EVENT
|
|
#define CONFIG_MKBP_EVENT_WAKEUP_MASK 0
|
|
#define CONFIG_KEYBOARD_PROTOCOL_MKBP
|
|
#define CONFIG_MKBP_USE_GPIO_AND_HOST_EVENT
|
|
|
|
/* Sensors */
|
|
#define CONFIG_ALS
|
|
#define ALS_COUNT 1
|
|
#define CONFIG_ALS_OPT3001
|
|
#define OPT3001_I2C_ADDR_FLAGS OPT3001_I2C_ADDR1_FLAGS
|
|
#define CONFIG_ACCEL_FIFO 512 /* Must be a power of 2 */
|
|
/* Depends on how fast the AP boots and typical ODRs */
|
|
#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO / 3)
|
|
#define CONFIG_ACCEL_INTERRUPTS
|
|
#define CONFIG_ACCELGYRO_BMI160
|
|
#define CONFIG_ACCELGYRO_BMI160_INT_EVENT \
|
|
TASK_EVENT_MOTION_SENSOR_INTERRUPT(LID_ACCEL)
|
|
#define CONFIG_SYNC
|
|
#define CONFIG_SYNC_INT_EVENT \
|
|
TASK_EVENT_MOTION_SENSOR_INTERRUPT(VSYNC)
|
|
#define CONFIG_TEMP_SENSOR
|
|
#define CONFIG_TEMP_SENSOR_BD99992GW
|
|
#define CONFIG_THERMISTOR_NCP15WB
|
|
|
|
/* SoC */
|
|
#define CONFIG_BOARD_HAS_RTC_RESET
|
|
#define CONFIG_CHIPSET_SKYLAKE
|
|
#define CONFIG_CHIPSET_HAS_PLATFORM_PMIC_RESET
|
|
#define CONFIG_CHIPSET_RESET_HOOK
|
|
#define CONFIG_CPU_PROCHOT_ACTIVE_LOW
|
|
#define CONFIG_DPTF
|
|
#define CONFIG_POWER_COMMON
|
|
#define CONFIG_POWER_BUTTON
|
|
#define CONFIG_POWER_BUTTON_X86
|
|
#define CONFIG_POWER_S0IX
|
|
#define CONFIG_POWER_TRACK_HOST_SLEEP_STATE
|
|
|
|
/* USB PD */
|
|
#define CONFIG_USB_PD_ALT_MODE
|
|
#define CONFIG_USB_PD_ALT_MODE_DFP
|
|
#define CONFIG_USB_PD_COMM_LOCKED
|
|
#define CONFIG_USB_PD_DISCHARGE_PPC
|
|
#define CONFIG_USB_PD_DUAL_ROLE
|
|
#define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE
|
|
#define CONFIG_USB_PD_LOGGING
|
|
#define CONFIG_USB_PD_PORT_COUNT 2
|
|
#define CONFIG_USB_PD_TCPC_LOW_POWER
|
|
#define CONFIG_USB_PD_TCPM_PS8805
|
|
#define CONFIG_USB_PD_TCPM_TCPCI
|
|
#define CONFIG_USB_PD_TCPM_MUX
|
|
#define CONFIG_USB_PD_TRY_SRC
|
|
#define CONFIG_USB_PD_VBUS_DETECT_TCPC
|
|
#define CONFIG_USB_PD_VBUS_MEASURE_NOT_PRESENT
|
|
#define CONFIG_USB_POWER_DELIVERY
|
|
#define CONFIG_USBC_PPC_SN5S330
|
|
#define CONFIG_USBC_SS_MUX
|
|
#define CONFIG_USBC_SS_MUX_DFP_ONLY
|
|
#define CONFIG_USBC_VCONN
|
|
#define CONFIG_USBC_VCONN_SWAP
|
|
|
|
/* Define typical operating power and max power. */
|
|
#define PD_MAX_VOLTAGE_MV 20000
|
|
#define PD_MAX_CURRENT_MA 3000
|
|
#define PD_MAX_POWER_MW 45000
|
|
#define PD_OPERATING_POWER_MW 15000
|
|
#define PD_VCONN_SWAP_DELAY 5000 /* us */
|
|
|
|
/* TODO(aaboagye): Verify these timings. */
|
|
/*
|
|
* delay to turn on the power supply max is ~16ms.
|
|
* delay to turn off the power supply max is about ~180ms.
|
|
*/
|
|
#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */
|
|
#define PD_POWER_SUPPLY_TURN_OFF_DELAY 250000 /* us */
|
|
|
|
/* I2C config */
|
|
#define I2C_PORT_CHARGER I2C_PORT_POWER
|
|
#define I2C_PORT_PMIC I2C_PORT_POWER
|
|
#define I2C_PORT_POWER NPCX_I2C_PORT0_0
|
|
#define I2C_PORT_BATTERY NPCX_I2C_PORT4_1
|
|
#define I2C_PORT_ALS_GYRO NPCX_I2C_PORT5_0
|
|
#define I2C_PORT_ACCEL I2C_PORT_ALS_GYRO
|
|
#define I2C_PORT_USB_C0 NPCX_I2C_PORT1_0
|
|
#define I2C_PORT_USB_C1 NPCX_I2C_PORT2_0
|
|
#define I2C_PORT_THERMAL I2C_PORT_PMIC
|
|
|
|
#define GPIO_USB_C0_SCL GPIO_EC_I2C1_USB_C0_SCL
|
|
#define GPIO_USB_C0_SDA GPIO_EC_I2C1_USB_C0_SDA
|
|
#define GPIO_USB_C1_SCL GPIO_EC_I2C2_USB_C1_SCL
|
|
#define GPIO_USB_C1_SDA GPIO_EC_I2C2_USB_C1_SDA
|
|
|
|
#define I2C_ADDR_MP2949_FLAGS 0x20
|
|
#define I2C_ADDR_BD99992_FLAGS 0x30
|
|
|
|
/*
|
|
* Remapping of schematic GPIO names to common GPIO names expected (hardcoded)
|
|
* in the EC code base.
|
|
*/
|
|
#define GPIO_AC_PRESENT GPIO_ACOK_OD
|
|
#define GPIO_ENABLE_BACKLIGHT GPIO_EC_BL_DISABLE_ODL
|
|
#define GPIO_BAT_PRESENT_L GPIO_EC_BATT_PRES_L
|
|
#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW
|
|
#define GPIO_PCH_PWRBTN_L GPIO_EC_PCH_PWR_BTN_L
|
|
#define GPIO_PCH_RSMRST_L GPIO_RSMRST_L
|
|
#define GPIO_PCH_SLP_S0_L GPIO_SLP_S0_L
|
|
#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L
|
|
#define GPIO_PCH_SLP_S4_L GPIO_SLP_S4_L
|
|
#define GPIO_PCH_SLP_SUS_L GPIO_SLP_SUS_L_PCH
|
|
#define GPIO_PCH_WAKE_L GPIO_EC_PCH_WAKE_L
|
|
#define GPIO_PMIC_DPWROK GPIO_ROP_DSW_PWROK_EC
|
|
#define GPIO_PMIC_SLP_SUS_L GPIO_SLP_SUS_L_PMIC
|
|
#define GPIO_POWER_BUTTON_L GPIO_EC_PWR_BTN_IN_ODL
|
|
#define GPIO_CPU_PROCHOT GPIO_EC_PROCHOT_ODL
|
|
#define GPIO_RSMRST_L_PGOOD GPIO_ROP_EC_RSMRST_L
|
|
#define GPIO_VOLUME_UP_L GPIO_H1_EC_VOL_UP_ODL
|
|
#define GPIO_VOLUME_DOWN_L GPIO_H1_EC_VOL_DOWN_ODL
|
|
#define GPIO_WP_L GPIO_EC_WP_L
|
|
|
|
#ifndef __ASSEMBLER__
|
|
|
|
#include "gpio_signal.h"
|
|
#include "registers.h"
|
|
|
|
/* ADC signal */
|
|
enum adc_channel {
|
|
ADC_BASE_ATTACH,
|
|
ADC_BASE_DETACH,
|
|
ADC_CH_COUNT
|
|
};
|
|
|
|
enum temp_sensor_id {
|
|
TEMP_SENSOR_BATTERY, /* BD99956GW TSENSE */
|
|
TEMP_SENSOR_AMBIENT, /* BD99992GW SYSTHERM0 */
|
|
TEMP_SENSOR_CHARGER, /* BD99992GW SYSTHERM1 */
|
|
TEMP_SENSOR_DRAM, /* BD99992GW SYSTHERM2 */
|
|
TEMP_SENSOR_EMMC, /* BD99992GW SYSTHERM3 */
|
|
TEMP_SENSOR_GYRO, /* BMI160 */
|
|
TEMP_SENSOR_COUNT
|
|
};
|
|
|
|
enum pwm_channel {
|
|
PWM_CH_DB0_LED_RED = 0,
|
|
PWM_CH_DB0_LED_GREEN,
|
|
PWM_CH_DB0_LED_BLUE,
|
|
PWM_CH_DB1_LED_RED,
|
|
PWM_CH_DB1_LED_GREEN,
|
|
PWM_CH_DB1_LED_BLUE,
|
|
PWM_CH_COUNT
|
|
};
|
|
|
|
/*
|
|
* Motion sensors:
|
|
* When reading through IO memory is set up for sensors (LPC is used),
|
|
* the first 2 entries must be accelerometers, then gyroscope.
|
|
* For BMI160, accel and gyro sensors must be next to each other.
|
|
*/
|
|
enum sensor_id {
|
|
LID_ACCEL,
|
|
LID_GYRO,
|
|
LID_ALS,
|
|
VSYNC,
|
|
SENSOR_COUNT,
|
|
};
|
|
|
|
#define CONFIG_ACCEL_FORCE_MODE_MASK BIT(LID_ALS)
|
|
|
|
void base_pwr_fault_interrupt(enum gpio_signal s);
|
|
int board_get_version(void);
|
|
|
|
/* Reset all TCPCs. */
|
|
void board_reset_pd_mcu(void);
|
|
void board_set_tcpc_power_mode(int port, int mode);
|
|
|
|
#endif /* __ASSEMBLER__ */
|
|
|
|
#endif /* __CROS_EC_BOARD_H */
|